Search
Products
    Menu Close

    Advanced Double Counter Top and Under Counter System Filter Set - 10" Antibacterial 1 Micron & 10" Pleated Filter

    Manufacturer: FIlterShop.co.za
    Replacement Antibacterial 1 Micron and Pleated Filter for Double Under Counter and Counter Top Systems
    *
    R0,00
    i h

    Advanced Double Counter Top and Under Counter System Filter Set - 10" 1 Micron & 10" Pleated Filter (0.1um)

     

    This Filter Set will fit double countertops, and under-the-counter systems, provided that the system uses the standard 10" Size Housings. 

     The advanced Double Countertop and Under the counter Filter set one major over the standard Filter Set:

    • The first stage filter is a 1-micron Anti-bacterial Melted Spray cartridge, rather than the normal 1-micron Melted Spray cartridge. The Anti-Bacterial Melted Spray cartridges have a bacteriostatic function which helps to inhibit the growth of bacteria on the surface of the filter, helping to ensure healthier product water and a longer life span of the filter. 

     

    Filter Description:

    Stage 1: 1um (Micron) Sediment Filter:
    This removes particles from the water down to 1 micron.

     

    Stage 2: Absolute Pleated Filter Cartridge (0.1 Micron):

    Filters the water down to 0.1um micron Capturing bacteria and very fine particles. 

    Flushing the system:

    This is done by running water through the system until the preservative cannot be detected in a sample glass of water. The preservative leaves a “film” on the water and also has a bitter taste. If you are seeing this in your water after a new installation, flush and test until no hints of the preservative can be detected. Please note if there is a white color to the water that settles out towards the top of the glass, this is most likely caused by tiny air bubbles in the water. This is caused by the Ultra Filtration membrane and is completely normal. This should subside over time as excess air in the system is removed. The air bubbles in the water will not affect the quality of your drinking water

    Filter Change Call Outs:

    This service is solely for clients based in and around the Centurion, Pretoria and Johannesburg areas.

    Filtershop now offers you the option to have your filter systems filters be replaced by one of our technicians. Our callout fee is dependent on how far you are situated from us, as we calculate this on a sliding scale. 

    If you are interested in having one of our technicians come to your home, business or site to have your filters replaced, please contact us via email: [email protected] and we will get back to you with more information.

     

    How to remove/replace your filter:

    Start by unscrewing the filter housing from the filtration unit. This is done by rotating the filter housing in a clockwise direction (see diagram below). The filter housing will separate from the filtration unit, and you are now free to remove the filter cartridge from the filter housing. To replace your filter: insert the new filter into the filter housing. Be sure to remove any protective plastic wrapping from the filter cartridge before placing them into the filter housing. Check that the black rubber O-rings are in place and fit well on the filter housing. If they seem perished or lose you may want to purchase new O-rings to ensure a good seal. As an option you can add a little bit of Vaseline on the O-rings to make them seal better, this will make it easier to open next time. Take note of any rubber seals on the filter cartridges, usually the KDF. These will need to face upwards to connect and seal at the top of the filter housing. It is important that this is done correctly as the system will not work optimally if the filters are installed incorrectly. Now that your filter is in the housing, bring the housing to the filtration unit and begin to screw the two together. This is done by rotating the filter housing in an anti-clockwise direction. We recommend you tighten by hand as this is usually sufficient to maintain a good seal. If however, leaks are detected, the housing spanner can be used to tighten the filter housings until a good seal is achieved. (Check O-rings are correctly in position before tightening with the spanner) Please take care not to over-tighten the filter housings. This could strip the housing thread and cause your system to fail. It will also make it more difficult to replace filters in the future if they are over-tightened. 

    When to change your filters:

    Filter lifespan is determined by the quality of the source water that runs through them. So if your source water is of a very bad quality, your filters will be doing more “work” to clean the water that is flowing through them. Thus depleting sooner than filters running under good water conditions. So, in short, each end-users filter requirements will be different as their source waters are different. We advise you check your filters on a monthly basis after initial install to get a feel for the quality of the water in your area. You will see for example, that the stage 1 filter (1um Sediment) is turning brown from the outside towards the center over a period of 12 months. If this is the case, your water quality is exceptionally good as these filters generally only have a lifespan of 4 - 12 months filtering average South African water. If your water quality is very poor you may be replacing the 1um sediment filter every 2 months. So visual inspection of your filters is the best way to determine when to change your filters. For the KDF  the “symptoms” are a little different. These filters are depleted once bacteria have colonized them completely. So in testing, you will want to see if any traces of bacteria can be detected. This is done by physically inspecting the filter cartridges. You want to check for a “slime” on the filters. This is a slippery substance and will feel similar to a mucus of sorts. If this is present on your filter cartridge then bacteria have colonized the filter and a replacement cartridge is required.

     

    Adding a Housing Spanner

    Over time the housing can become tight, and difficult to open by hand. If you do not already have one available to open the housings, we would recommend adding a housing spanner. 

    The Housing Spanner will allow you to gain more "purchase" on the housing, allowing you to open it more easily. 

     

     

     

     

    *
    *
    *